• MPP charge current increase compared to conventional controllers by using the latest controller technology (microprocessor) by 10% to 30% (efficiency > 95%). The performance plus shows in particular to the cooler season and e.g. in high snow, lower and diffuse lighting (wintering).
• For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and support charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.
• Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of too low solar power e.g. twilight, at night, etc.).
• Parallel / buffer operation: Compliance with the charging regulations even with simultaneous operation of consumers.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides for equalization charging of the individual battery cells (lead and lith.), then automatic trickle charge (U2).
• Charge cable compensation: Voltage losses on the charging cables are automatically compensated.
• Bordnetzfilter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc..
• CI-Bus connection: to display all relevant data on a central vehicle display
• Measurement output for EBL, possibly existing electrical block in the living area of the vehicle: Allows the convenient use of a built-in (solar) current display in the electrical block to control the solar system.
• Please check in advance necessarily the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel, as we can not assume any warranty for this.
• Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes the automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus.
• Connection for battery temperature sensor (Art. No. 2001): For lead-acid batteries, the automatic adjustment of the charging voltage to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided.
• LiFePO4 batteries: Battery protection at high and especially at low temperatures.Absolutely recommended if the battery temperature can fall below 0 ° C during operation.
• Plug ready for connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system.

Further specifications:

• Nominal battery voltage (AC) in [V]: 12
• Solar module power max [Wp]: 360
• Solar module current max [A]: 21
• Solar module voltage max [V]: 60
• Charge current Batt. I / II max. [A]: 26.0 / 1.5
• Charge characteristic: IU1oU2
• Battery type adjustable: acid, gel, AGM, LiFePO4
• Own consumption in [A]: 0.004
• Overcharge protection: yes
• Back current lock (night operation): yes
• Bordnet filter: yes
• Number of charge outputs: 2
• Protection against overload, overheating, reverse polarity: yes
• Port temperature sensor: yes
• Compensation of voltage losses on the charging cables: yes
• Port LCD solar computer S: yes
• Output EBL solar current display: yes
• Temperature range [°C]: -20 to +45

• Up to 360 Wp module power
• Max. 21 A module current
• Max. 60 V module voltage
• Charging possibilities: 1 supply and 1 starter battery
• 4 loading programs

• TOP controller in shunt technology
• Additional charging output for starter battery
• Charging characteristic adjustable for all battery types
• Power indicator with LEDs
• Temperature sensor can be connected
• Solar display and solar monitor connectable (also EBL)

• TOP controller in shunt technology
• Additional charging output for starter battery
• Charging characteristic for all battery types
• Power indicator with LEDs
• Temperature sensor can be connected
• All controllers with connection for solar display or solar monitor

• TOP controllers in series technology
• 2. output for starter battery
• Charging programs for all battery types (including lithium ions)
• Battery indicator with LEDs
• Temperature sensor can be connected
• All controllers can be connected to solar computer (also to Schaudt EBL)

• TOP controller in shunt technology
• Additional charging output for starter battery
• Charging programs for all battery types
• LED power indicator
• Temperature sensor can be connected
• Connectable to solar display, solar monitor and Schaudt EBL

• Battery voltage: on-board & starter battery
• Level indicator: Fresh & waste water tank
• Main switch - Function
• Undervoltage protection for the on-board battery
• pump master switch
• Solar Computer 12V VPC Terra

• MPP charging current increase compared to conventional controllers by using the latest controller technology (microprocessor) by 10% to 30% (efficiency > 95%). The performance plus shows in particular to the cooler season and e.g. in high snow, lower and diffuse lighting (wintering).
• For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and support charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.
• Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of too low solar power e.g. twilight, at night, etc.).
• Parallel / buffer operation: Compliance with the charging regulations even with simultaneous operation of consumers.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides for equalization charging of the individual battery cells (lead and lith.), then automatic trickle charge (U2).
• Charge cable compensation: Voltage losses on the charging cables are automatically compensated.
• Bordnetzfilter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc..
• CI-Bus connection: to display all relevant data on a central vehicle display
• Measurement output for EBL, possibly existing electrical block in the living area of the vehicle: Allows the convenient use of a built-in (solar) current display in the electrical block to control the solar system.
• Please check in advance necessarily the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel, as we can not assume any warranty for this.
• Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes the automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation when permanently abundant solar power surplus.
• Connection for battery temperature sensor: For lead-acid batteries, the automatic adjustment of the charging voltage to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures, unnecessary battery gassing and load is avoided.
• LiFePO4 batteries: Battery protection at high and especially at low temperatures.Absolutely recommended if the battery temperature can fall below 0 ° C during operation.
• Plug-ready for connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 170 Wp module output
• For solar modules with max. 10 A module current
• For solar modules with max. 60 V module voltage
• Charging possibility for 1 supply and 1 starter battery
• With charging characteristic for lithium batteries

• MPP charge current increase compared to conventional controllers by using the latest controller technology (microprocessor) by 10% to 30% (efficiency > 95%). The performance plus shows in particular to the cooler season and e.g. in high snow, lower and diffuse lighting (wintering).
• For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and support charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.
• Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of too low solar power e.g. twilight, at night, etc.).
• Parallel / buffer operation: Compliance with the charging regulations even with simultaneous operation of consumers.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides for equalization charging of the individual battery cells (lead and lith.), then automatic trickle charge (U2).
• Charge cable compensation: Voltage losses on the charging cables are automatically compensated.
• Bordnetzfilter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc..
• CI-Bus connection: to display all relevant data on a central vehicle display
• Measurement output for EBL, possibly existing electrical block in the living area of the vehicle: Allows the convenient use of a built-in (solar) current display in the electrical block to control the solar system.
• Please check in advance necessarily the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel, as we can not assume any warranty for this.
• Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes the automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus.
• Connection for battery temperature sensor (Art. No. 2001): For lead-acid batteries, the automatic adjustment of the charging voltage to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided.
• LiFePO4 batteries: Battery protection at high and especially at low temperatures.Absolutely recommended if the battery temperature can fall below 0 ° C during operation.
• Plug-ready for connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 260 Wp module output
• For solar modules with max. 15 A module current
• For solar modules with max. 60 V module voltage
• Charging possibility for 1 supply and 1 starter battery
• With charging characteristic for lithium batteries

• MPP charging current increase compared to conventional controllers by using the latest controller technology (microprocessor) by 10% to 30% (efficiency > 95%). The performance plus shows in particular to the cooler season and e.g. in high snow, lower and diffuse lighting (wintering).
• For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and support charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.
• Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of too low solar power e.g. twilight, at night, etc.).
• Parallel / buffer operation: Compliance with the charging regulations even with simultaneous operation of consumers.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides for equalization charging of the individual battery cells (lead and lith.), then automatic trickle charge (U2).
• Charge cable compensation: Voltage losses on the charging cables are automatically compensated.
• Bordnetzfilter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc..
• CI-Bus connection: to display all relevant data on a central vehicle display
• Measurement output for EBL, possibly existing electrical block in the living area of the vehicle: Allows the convenient use of a built-in (solar) current display in the electrical block to control the solar system.
• Please check in advance necessarily the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel, as we can not assume any warranty for this.
• Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes the automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus.
• Connection for battery temperature sensor (Art. No. 2001): For lead-acid batteries, the automatic adjustment of the charging voltage to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided.
• LiFePO4 batteries: Battery protection at high and especially at low temperatures.Absolutely recommended if the battery temperature can fall below 0 ° C during operation.
• Plug-ready for connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system.

• Advanced power and charging capability
• With charging characteristic for lithium batteries
• Integrated CI bus interface
• Charging possibilities: 1 supply and 1 starter battery
• For solar modules with: up to 440 Wp module output
• For solar modules with: max. 26 A module current
• For solar modules with: max. 60 V module voltage

The solar regulator is specially designed for use in motorhomes and caravans and is suitable for all lead-acid battery types and brands (acid, GEL/dryfit and AGM / fleece batteries). Through intelligent microprocessor control, the batteries are charged optimally with IU1oU2 characteristics. The solar controller operates fully automatically and maintenance-free and offers the following functions:

• Charge output board battery I , depending on battery type optionally 4 charging programs
• Charge output starter battery II: Separate secondary charge output with reduced charge current (24 V / 0.8 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle times.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main or on-board battery (board I). Support charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging.
• Supervised charging: Standard protection against battery back discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating.
• Buffer operation: Compliance with the charging characteristics even in simultaneous operation with consumers on the battery.
• Overcharge protection: Regulates the charging current of the battery in case of too much solar power and full battery back, provides power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charge voltage increase (U1) prevents harmful acid stratification and provides for equalization charging of the individual battery cells, then automatic trickle charge (U2).
• Bordnetzfilter: Built-in, allows the trouble-free parallel operation of the controller with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on a battery.
• Connection for temperature sensor: Automatic adjustment of the charging voltage to the battery temperature. Causes in cold weather a better full charge of the weaker battery, in summer temperatures unnecessary battery gassing is avoided.
• Unconditionally recommended when the battery is exposed to strong temperature fluctuations, eg in the engine compartment.
• Charging cable compensation: voltage losses on the charging cables are automatically compensated.
• Plug ready for connection of the Votronic solar display units LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 300 Wp module output
• For solar modules with max. 10 A module current
• For solar modules with max. 50 V module voltage
• Charging possibilities 1 supply and 1 starter battery

• Charge output board battery I , charging programs 1, 2 and 4 (gel, AGM, acid) on battery type adjustable.
• Charge output starter battery II: Separate secondary charge output with reduced charging current (12 V / 0.8 A resp. 1.5 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle times.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main or on-board battery (board I). Support charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging.
• Supervised charging: Standard protection against battery back discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating.
• Buffer operation: Compliance with the charging characteristics even in simultaneous operation with consumers on the battery.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charge voltage increase (U1) prevents harmful acid stratification and provides for equalization charging of the individual battery cells, then automatic trickle charge (U2).
• Bordnetzfilter: Built-in, allows the trouble-free parallel operation of the controller with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on a battery.
• Connection for temperature sensor: Automatic adjustment of the charging voltage to the battery temperature. Causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided.
• Unconditionally recommended when the battery is exposed to large temperature fluctuations, eg in the engine compartment.
• Charging cable compensation: voltage losses on the charging cables are automatically compensated.
• Measurement output for EBL (electric block of the vehicle): Allows convenient use of the (solar) current display built into the electric block to control the solar system.
• Please be sure to check in advance the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel, as we can not provide any warranty for this.
• Switching output "AES" (only SR 350 CI and SR 550 CI): Causes the automatic switching of ELECTROLUX-/DOMETIC refrigerators with "AES" (Automatic Energy Selector) from gas to 12 V operation in case of abundant solar power surplus.
• Plug-ready for the connection of the Votronic solar display units LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 150 Wp module output
• For solar modules with max. 9.5 A module current
• For solar modules with max. 28 V module voltage
• Charging possibilities 1 supply and 1 starter battery

• Charge output board battery I , charging programs 1, 2 and 4 (gel, AGM, acid) on battery type adjustable.
• Charge output starter battery II: Separate secondary charge output with reduced charging current (12 V / 0.8 A resp. 1.5 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle times.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main or on-board battery (board I). Support charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging.
• Supervised charging: Standard protection against battery back discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating.
• Buffer operation: Compliance with the charging characteristics even in simultaneous operation with consumers on the battery.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charge voltage increase (U1) prevents harmful acid stratification and provides for equalization charging of the individual battery cells, then automatic trickle charge (U2).
• Bordnetzfilter: Built-in, allows the trouble-free parallel operation of the controller with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on a battery.
• Connection for temperature sensor: Automatic adjustment of the charging voltage to the battery temperature. Causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided.
• Unconditionally recommended when the battery is exposed to large temperature fluctuations, eg in the engine compartment.
• Charging cable compensation: voltage losses on the charging cables are automatically compensated.
• Measurement output for EBL (electric block of the vehicle): Allows convenient use of the (solar) current display built into the electric block to control the solar system.
• Please be sure to check in advance the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel, as we can not provide any warranty for this.
• Switching output "AES" (only SR 350 CI and SR 550 CI): Causes the automatic switching of ELECTROLUX-/DOMETIC refrigerators with "AES" (Automatic Energy Selector) from gas to 12 V operation in case of abundant solar power surplus.
• Plug-ready for the connection of the Votronic solar display units LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 230 Wp module output
• For solar modules with max. 14.5 module current
• For solar modules with max. 28 V module voltage
• Charging possibilities 1 supply and 1 starter battery

• Charge output board battery I , charging programs 1, 2 and 4 (gel, AGM, acid) on battery type adjustable.
• Charge output starter battery II: Separate secondary charge output with reduced charging current (12 V / 0.8 A resp. 1.5 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle times.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main or on-board battery (board I). Support charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging.
• Supervised charging: Standard protection against battery back discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating.
• Buffer operation: Compliance with the charging characteristics even in simultaneous operation with consumers on the battery.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charge voltage increase (U1) prevents harmful acid stratification and provides for equalization charging of the individual battery cells, then automatic trickle charge (U2).
• Bordnetzfilter: Built-in, allows the trouble-free parallel operation of the controller with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on a battery.
• Connection for temperature sensor: Automatic adjustment of the charging voltage to the battery temperature. Causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided.
• Unconditionally recommended when the battery is exposed to large temperature fluctuations, eg in the engine compartment.
• Charging cable compensation: voltage losses on the charging cables are automatically compensated.
• Measurement output for EBL (electric block of the vehicle): Allows convenient use of the (solar) current display built into the electric block to control the solar system.
• Please be sure to check in advance the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel, as we can not provide any warranty for this.
• Switching output "AES" (only SR 350 CI and SR 550 CI): Causes the automatic switching of ELECTROLUX-/DOMETIC refrigerators with "AES" (Automatic Energy Selector) from gas to 12 V operation in case of abundant solar power surplus.
• Plug-ready for the connection of the Votronic solar display units LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 350 Wp module output
• For solar modules with max. 22 A module current
• For solar modules with max. 28 V module voltage
• Charging possibilities 1 supply and 1 starter battery

• Charge output board battery I , charging programs 1, 2 and 4 (gel, AGM, acid) on battery type adjustable.
• Charge output starter battery II: Separate secondary charge output with reduced charging current (12 V / 0.8 A resp. 1.5 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle times.
• The charging voltage is free of peaks and regulated so that overcharging of the batteries is excluded.
• Two battery charging outputs: Automatic charging of the main or on-board battery (board I). Support charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging.
• Supervised charging: Standard protection against battery back discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating.
• Buffer operation: Compliance with the charging characteristics even in simultaneous operation with consumers on the battery.
• Overcharge protection: Regulates the charging current of the battery with too much solar power and full battery back, provides for power consumption by immediate recharging for the highest possible state of charge of the battery.
• "IU1oU2" charging characteristic: Defined charge voltage increase (U1) prevents harmful acid stratification and provides for equalization charging of the individual battery cells, then automatic trickle charge (U2).
• Bordnetzfilter: Built-in, allows the trouble-free parallel operation of the controller with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on a battery.
• Connection for temperature sensor: Automatic adjustment of the charging voltage to the battery temperature. Causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing is avoided.
• Unconditionally recommended when the battery is exposed to large temperature fluctuations, eg in the engine compartment.
• Charging cable compensation: voltage losses on the charging cables are automatically compensated.
• Measurement output for EBL (electric block of the vehicle): Allows convenient use of the (solar) current display built into the electric block to control the solar system.
• Please be sure to check in advance the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel, as we can not provide any warranty for this.
• Switching output "AES" (only SR 350 CI and SR 550 CI): Causes the automatic switching of ELECTROLUX-/DOMETIC refrigerators with "AES" (Automatic Energy Selector) from gas to 12 V operation in case of abundant solar power surplus.
• Plug-ready for the connection of the Votronic solar display units LCD-Solar Computer S for optimal control of the system.

• For solar modules with up to 550 Wp module output
• For solar modules with max. 35 A module current
• For solar modules with max. 28 V module voltage
• Charging possibilities 1 supply and 1 starter battery